This article was co-authored by Chad Zani. Chad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide.
wikiHow marks an article as reader-approved once it receives enough positive feedback. This article has 15 testimonials from our readers, earning it our reader-approved status.
This article has been viewed 1,039,872 times.
The moment you discover that your vehicle is covered in tree sap your heart usually sinks, not just because your shiny car is now dirty, but because of the work it will take to remove the sap. Cleaning sap off of your car can be a tedious process, can potentially scratch your car paint, and going through a carwash might not do the trick. However, there are several ways to remove sap from your car that will make the task much easier. Follow one of these methods to restore the clean, shiny surface of your car.
Steps
Washing Your Car with Soap and Hot Water
-
1Wash your car as soon as possible. The longer tree sap or any substances like sap (and bird droppings or insect remains for that matter) are left on the surface of the vehicle, the more difficult they are to remove. Acting fast will require the least amount of effort and the most success at getting a sparkling car exterior.
-
2Spray off your car with clean water. Giving your car this initial rinse will get all the large debris off but it will also help you to see where you need to focus further cleaning.
- Take the time to wash your whole car, even if it's not all covered in sap. You will be more satisfied when you get the sap off if your whole car is nice and clean. Besides, you already have all the supplies out and ready to go.
Advertisement -
3Rub the surface with a microfiber rag covered in hot, soapy water. Use the hottest water you can, as the sap will be weakened most effectively by really hot water.
- Before using other methods of sap removal, try cleaning your car with really hot water. If the sap gets removed, then great, you are done. If the sap remains, at least you have a clean surface on which to try other methods.
- Be sure that your rag is clean and that you rinse it often to get any debris and sap out. Using a dirty rag will only spread this across the surface of your car.
-
4Rinse the surface repeatedly. Rinsing the area you are cleaning will allow you to see if your job is done or if you need to use more elbow grease to get the sap removed.
-
5Dry and wax the surface of your car once the sap is removed. All the cleaning you have done has effectively removed the sap but it has probably also removed any wax that was protecting the surface. Use your usual method of waxing your car or, if you have never waxed your car before, consult How to Wax You Car for directions.
Removing Sap with a Commercial Remover
-
1Wash your car with soap and hot water. Make sure to get all the dirt and grime off the surface around the sap. If attempting to get the sap off with the hot water and soap doesn't work, continue with these steps.
- Even if the wash doesn't get the sap off, the warmth of the water will begin to soften it, making it easier to remove. This is also helpful if the sap has been on the car for a while.
-
2Buy commercial tree sap remover and review the instructions on the container. This should be available at any auto-parts store. Using this type of product is a highly recommended way to remove sap from your car because it is formulated to dissolve sap effectively without hurting your car's exterior.
-
3Place some of the remover on a clean rag. Then hold the rag on the sap while gently applying pressure for a minute or so. The remover should soak into the sap, breaking down the connection between the sap and your car's surface.
-
4Rub in a circular motion over the sap to lift it from the surface. Be relatively gentle while doing this, as you don't want to spread any of the sap across the surface of your car.
-
5Finish by washing and waxing your car.[1] Rewashing you car will help remove any residue left over from the sap or the cleaner used to remove it. A new coating of wax is recommended to renew the protective coating on the vehicle, making sure your car has a beautiful, shiny surface.
Removing Sap with Products from the Home
-
1Wash your car with soap and hot water. Make sure to get all the dirt and grime off the surface around the sap. If attempting to get the sap off with the hot water and soap doesn't work, continue with these steps.
- Even if the wash doesn't get the sap off, the warmth of the water will begin to soften it, making it easier to remove. This is also helpful if the sap has been on the car for a while.
-
2Use a household product to remove the sap.There are a variety of products that you may have in your home already that can remove tree sap effectively.[2] Be sure to use them sparingly and test them on a hidden area of your paint job before applying to any sap, as none of them are made specifically for the surface of a car.
- Try mineral spirits or alcohol wipes. Mineral spirits applied lightly with a soft cloth will break down the sap and remove it but it has the potential of damaging your car's surface. Do not rub too vigorously or for too long so that the paint job is not damaged.
- Mineral spirits and alcohol wipes should be tried separately. Use the previous directions and try with mineral spirits. If that fails, use readily available 91% isopropyl alcohol instead of mineral spirits. Alcohol evaporates quickly and although your cloth will seem wet, it is the water that is left after the alcohol evaporates. Keep your cloth wet with fresh alcohol and move quickly with light pressure. This will easily remove hard dried as well as fresh pine tree sap.
- Spray WD-40 on the tree sap.[3] The sap will begin to absorb the solvent. Let it sit for a few minutes. You can use your rag to lift the loosened sap from the car.
- Rub hand sanitizer on the tree sap. Place a small amount of hand sanitizer on the sap and let it set for a few minutes. Rub with a clean cloth and the sap dissolves right off.[4]
-
3Finish with a regular car wash and wax. The car wash will help remove any residue left over from the sap or the cleaner used to remove it. Any solution that would deteriorate paint will be washed away. A new coating of wax is recommended to renew the protective coating on the vehicle.
Expert Q&A
Did you know you can get expert answers for this article?
Unlock expert answers by supporting wikiHow
-
QuestionHow do you get dried sap off a car?
Chad ZaniChad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide.
Auto Detailing ExpertSome of the worst damage I've seen in my time working on vehicles was the result of someone attempting to remove crystallized tree sap from their car. The crystals scratch the surface just like glass. Softening the tree sap before trying to remove it is very important for getting the job done correctly.
Support wikiHow by unlocking this expert answer.
-
QuestionWhich wax would give me the best shine?
Alex BozeCommunity AnswerMeguiar's wax seem to work best for me, although I have also heard very positive feedback about Turtle Wax brand as well. -
QuestionHow can I get hardened salt out of carpeting?
Community AnswerWash it with special spot treatment, or rub in a circular motion with laundry detergent.
Things You'll Need
- Water
- Soap
- Soft cloth
- Tree sap remover
- Mineral spirits
- WD-40
- Hand Sanitizer
- Car wax
- Popsicle sticks
References
About This Article
Getting sap off of your car without scratching the paint can be tricky, but don’t worry, there are several effective ways to tackle this sticky problem. The sap will be easier to get off if you wash it immediately, so get to work right away. To start, hose your whole car down with clean water to rinse away any loose sap and debris. This will also make it easier to spot any sappy stains you didn’t see before. Dip a clean microfiber rag in soapy water that’s as warm as possible without being too hot to touch. The heat will help soften the sap. Scrub the stains with the cloth and rinse as you go to immediately wash away any loose sap. While this technique shouldn’t damage the paint on your car, it might strip away some of the protective wax coating. Once you’re satisfied that all the sap is gone, wipe your car dry with a clean, soft towel and buff on a new layer of wax. If you still see some stubborn sap stains after cleaning your car, don’t wax it just yet. Follow up your soap-and-water wash with a commercial tree sap remover. You can buy this type of cleaner at most auto-parts stores, or in the automotive section of a department store. Follow the instructions on the package carefully to make sure you’re using the product correctly. Typically, all you have to do is pour a bit of the sap remover directly onto a clean rag, then hold the rag over the stain using even pressure for about 1 minute to break down the sap. Then, buff the sap away with the rag using small, circular motions. If you can’t find a store-bought sap remover, try dissolving the stain with a household product such as mineral spirits, alcohol wipes, or WD-40. When using any of these products, use a soft cloth and apply light pressure to avoid damaging your paint. After you’re done, re-wash the car with soap and water and apply a new coat of wax. For more tips on removing sap from your car, keep reading!
