This article was co-authored by Howard Fleischmann. Howard Fleischmann is an Automotive Tire and Repair Specialist and the CEO of Community Tire Pros & Auto Repair, with ten locations throughout Phoenix, Glendale, Yuma, and Casa Grande, Arizona. Howard specializes in full-service auto repair and tire replacement and care for domestic/imported vehicles and large trucks. Howard’s dedication to Community Tire Pros & Auto Repair has earned their team multiple awards and features including the 2021 Phoenix Magazine AZ State 48 “Best of the Best!”, the 2020 “Best of Phoenix” in Auto Repair, the 2013 Master SBD award, the 2013 National “Top Shop” award by Tire Review, the 2012 Diversity Champions Phx Business Journal, the 2009 BBB Ethics award, the 2008 Phx Chamber of Commerce Impact Award -” Small Business of the Year”, and the 2008 ASU Spirit of Enterprise award. Howard is often referred to as “The Car Guy” for local TV stations and is a regular on TV’s Channel 3 Sunday, Good Morning Arizona monthly.
There are 7 references cited in this article, which can be found at the bottom of the page.
This article has been viewed 59,368 times.
Did you know that you can repair your punctured tire, and not have to spend all that cash buying a brand new tire? If you're prepared to get a little greasy and do the legwork yourself, you can find yourself back on the road and enjoying the drive-in on time.
Steps
Patch a Punctured Tire
-
1Locate the tire that is losing air. Remove your valve caps first. You can either find the hole by looking for the nail that is pierced through the tire, or you can put the tire in a tub of water and roll it around in driving rotation. There should be air bubbles where the hole is.
-
2Take the tire off from the rim. This allows the puncture to be easily accessed.[1]Advertisement
-
3Remove anything that's in the tire. If you have found the hole, and there is a nail punctured through it, use your pliers. Grab from the threading of the nail and lift out the nail. Mark the hole with tire chalk for easy access.
-
4Once the hole is clear, squirt some buffering solution over the puncture. This allows the buffer to work effectively and leave you with a smooth surface.
-
5Grab your buffer machine. Make sure that you have a sanding pad surface on your buffer to get a smooth surface. Buff all around the punctured area in a circular motion to make sure you get everywhere you need.[2]
-
6Use a Tire Radial Patch. You can start by first removing the sticky pads of the inner side of the Radial Patch. Then from the inside of the tire, you can stick the Radial Patch through the hole about halfway with the aluminum side first.
-
7Spread the Tire Chemical Care (Seal Fast B-133). Using the brush at the end of the cap, spread the liquid material all around the Radial Patch string as shown in the picture.[3]
-
8Pull the rest of the Radial Patch through the tire. You must pull all the way through until the patch completely sits on the inner side of the tire, and the aluminum piece comes out of the rubber.
-
9Cut the long leftover end of the patch using your cutting pliers. Scissors will work too. As shown in the picture, you want to cut as low as you can.
-
10Roll over the patch. Using your Tire Retread and Repair Tool, run over the Radial Patch from the inside of the tire. You can roll it in any direction, as long as you make sure to get every spot of the patch. Once the steps have been completed, your tire is ready to hit me back on the rims and filled to the pressure needed to be back on the road.[4]
Temporary Fix on a Punctured Tire
- This fix is just temporary so that you can get to a mechanic for a permanent solution.
-
1Locate the tire that is losing air. Remove your valve caps first. You can either find the hole by looking for the nail that is pierced through the tire, or you can put the tire in a tub of water and roll it around in driving rotation. There should be air bubbles where the hole is.
-
2Keep the tire on the rim and expand the hole. Using the Pistol Grip Rasp Tool, you can insert it through the puncture moving it up and down. It will expand the hole if needed to fit the Tire Repair Refills in.[5]
-
3Spray Heavy Duty Silicone Lubricant over the punctured area.
-
4Grab the Pistol Grip Inserting Needle and take a piece of the Tire Repair Refills. Put the Tire Repair Refills piece through the Needle as shown in the picture.
-
5When the refill piece is placed in between the needle, you can hold from the pistol grip and pierce the needle through the hole and pull the needle back out. The Tire Repair Refill piece should be left inside the hole.[6]
-
6Cut off the refill piece that is sticking out of the tire using the cutting pliers or even scissors.[7] (If you have a lighter, you can even set the extra piece of the refill on fire).
Warnings
- Be careful when handling the lighter.⧼thumbs_response⧽
- Do not attempt to repair the tire if it's punctured or damaged on the sidewall⧼thumbs_response⧽
- Repair tire as soon as possible before driving, could lead to an accident⧼thumbs_response⧽
References
- ↑ https://www.youtube.com/watch?v=ePzUeFeovpA
- ↑ https://www.rabenwholesale.com/wp-content/uploads/sites/4/2018/06/Puncture-Repair-Procedure.pdf
- ↑ https://www.youtube.com/watch?v=-R8IZ_mPh_U
- ↑ https://www.youtube.com/watch?v=2QR1vag1N9Q
- ↑ https://www.youtube.com/watch?v=3aQRO29ZzbE
- ↑ https://youtu.be/6T-rmhXUR8o?t=260
- ↑ https://youtu.be/3aQRO29ZzbE?t=567