A car that is used is bound to obtain a few paint chips. Debris from the road kicks up while driving to chip the sides, adverse weather can wreak havoc on the hood, and accidents can happen any time. These chips are usually too small to warrant a new paint job or professional assistance at all. However, if the affected area is smaller than a pencil eraser, you can use touch-up paint to repair the damage yourself.

Part 1
Part 1 of 3:

Cleaning and Sanding the Surface

  1. 1
    Wash the car. Focus on deep cleaning the area where the paint is chipped. Making sure the area is clean will help you identify all the spots that need to be touched up and will reduce the risk of getting dirt and grime in the new paint.
    • Use car washing soap, water, and a clean, soft cloth to clean the scratched area.[1]
    • Be sure to thoroughly dry the area that is scratched after you wash it.
  2. 2
    Check for rust and remove any you find. Look at the scratched area for discoloration on the metal. If you find an area that is dark red or brown, it is likely rust. Use sand paper to remove all areas of discoloration and then wipe down the area with a dry cloth to remove any dust.[2]

    Note: Removing the rust will help minimize the chance of rust developing under the paint in the future.

    Advertisement
  3. 3
    Apply a wax and grease remover to the area being fixed. It’s important to remove any wax on areas that need to have paint adhere to them. Wax isn’t typically removed by soap and water, so a specific remover is needed.[3]
    • Wax removers are available at most auto parts stores. These rust removal products are made specifically for removing rust on the bodies of cars.
    EXPERT TIP
    Chad Zani

    Chad Zani

    Auto Detailing Expert
    Chad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide.
    Chad Zani
    Chad Zani
    Auto Detailing Expert

    Our Expert Agrees: You need to thoroughly prepare the area before you add any touch-up paint or the result might look bad. Remove all the wax and sealant on the area and make sure any dirt and grime are gone as well. Without prepping the spot first, the paint won't adhere well, and it could look 'globby.'

  4. 4
    Sand the area to prep the surface. Use a small piece of sandpaper to sand all around the scratch. Try to remove all loose paint from the area while you sand. This process will also give the touch-up paint a clean surface to stick to.[4]

    Tip: Sand the area with 220-grit sandpaper. This will allow the primer to stick.

  5. 5
    Wipe down the area once more. Wash the area with water to remove any leftover debris from the pre-treating process. Allow the area to dry thoroughly before moving on to the next step.
  6. Advertisement
Part 2
Part 2 of 3:

Priming and Painting Chipped Areas

  1. 1
    Figure out the exact paint color on your car. If your car has its original paint job, you can do an online search for your car's make, model, color, and the words "paint code." You can also look on the car for the code if you can't find it online. Check the door jam, near the VIN number, and on firewall (bulkhead) to find the paint code number.[5]

    Note: The firewall is the piece of sheet metal that separates the engine under the hood from the passengers inside the vehicle. You will need to open your hood to find this number.

  2. 2
    Buy a matching touch-up paint color. Go to your local auto parts store or contact your car dealership with your paint color in hand. If you have a common car, they will likely have touch up paint for your paint job in stock. If you have an unusual or rare car, they may have to order your touch up paint.[6]
    • Touch up paint comes in several types of containers. It often comes in small jars of the paint or in paint pens.
    • It's important to get an exact match to your car's color, so don't settle on a color that is just close to your car's.
    • Light-colored cars can be difficult to find a perfect color match. Consult an auto paint specialist if you are having difficulty finding the right color.
  3. 3
    Apply rust arrestor on the chipped area. Before touching the chipped area up, it’s important to prevent rust from spreading underneath your touch-up job in the future. Paint on a small amount of rust inhibitor over the chipped area before the primer.[7]

    Note: Rust arrestor is available at most auto parts stores. Make sure the one you use states on the package that it can be used under paint.

  4. 4
    Apply primer, if necessary. Squeeze a dab of primer onto the area if the chip reaches metal. If the chip is surface-level, you can skip this step. Primer is needed for deep chips because regular paint will not adhere to bare metal.[8]
    • Spread the primer around the small chip with a tiny brush. Only use enough primer for one thin coat.
    • Allow the primer to dry completely.
    • Avoid getting primer on the car paint outside of the chipped area. It will ruin the finish.
  5. 5
    Test the paint. Apply some of the paint to an area on the car that isn't visible, such as the lip under a door. It is important to make sure the paint you've purchased will not react poorly to your existing paint and also that it matches well.[9]

    Tip: Shake the paint well before testing it. This will ensure that the true color and consistency are tested.

  6. 6
    Apply the touch-up paint to the primed area. Spread 2 to 3 layers of touch-up paint on the area. The touched-up spot will look elevated above the rest of the paint, which is how it should look.[10]
    • If the paint chip is on a vertical surface on your car, it’s especially important to wait until the touch-up paint dries between layers so it doesn't run.
    • The painted area should be raised so that it can be sanded down smooth with the rest of the paint job once it is dry.
  7. 7
    Allow drying time between coats and after the layers are applied. Between each layer let the paint dry for an hour. This will ensure that each layer is set and doesn't get smeared by the next. Also, wait at least 24 hours before continuing the process after you have applied all your layers.
  8. Advertisement
Part 3
Part 3 of 3:

Finishing the Surface

  1. 1
    Sand the touched-up area until it is smooth. Start by sanding the area with 1000-grit sandpaper, making sure to move very slowly and gently. Once the touched-up area appears close to level with the rest of the pain, continue to sand gently with 2000-grit sandpaper. After that, rub the area with 3000-grit sandpaper until the touch-up paint is even with the rest of the vehicle.
    • As your sandpaper gets finer, it will remove less and less of the paint. Don’t be tempted to push really hard with the sandpaper because of this.
    • It is ok if you sand a small amount of the surrounding painted area. This will be fixed by the top coat you will apply over the whole area.
  2. 2
    Apply the top coat. Paint the top coat over the entire area that is discolored. Typically this includes the chipped area and the existing paint surrounding it that has been lightly sanded. Try to get the top coat as smooth and even as possible, using a clean brush, even strokes, as several thin layers.[11]
    • Allow your top coat to dry for 10 to 20 minutes between coats.
    • It’s best to apply several thin coats instead of one thick coat.
    • Follow the directions that came on your top-coat container. In some cases they will tell you to apply several coats and in others the directions will state that one coat is enough.
  3. 3
    Sand the area once more with 3000-grit sandpaper. Giving the surface one last sanding will ensure that the clear coat you applied is smooth and blended with the existing top coat. Sand it until the repaired area is flush with the rest of the paint surface on the car.[12]

    Note: At this point the chipped area should disappear into the rest of the paint job.

  4. 4
    Polish and wax the entire car. Once you have repaired your paint chips it’s nice to give your whole car a bit of care. Polishing and waxing the car will help the repaired area blend in with the rest of the paint job and it will protect the fixed area from more damage.[13]
  5. Advertisement

Community Q&A
Did you know you can get answers researched by wikiHow Staff? Unlock staff-researched answers by supporting wikiHow

  • Question
    Can I buy touch up paint for my car?
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer

    Support wikiHow by unlocking this staff-researched answer.

    Yes, you can. Touch-up paint for cars is available in a wide variety of colors to match many car colors. The paint will either be in the form of a paint pen or comes in a small container or jar. It’s a good idea to find the right name given to your car’s paint color, to get an exact color match. If you have difficulty matching the paint colors, speak to an auto paint specialist, who may be able to advise or even mix a suitable touch-up paint for you.
  • Question
    How do you touch up scratches on a car?
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer

    Support wikiHow by unlocking this staff-researched answer.

    Deep scratches may be able to be fixed by painting them. The basic steps involve sanding the affected area to remove the top layers of paint, rinsing after sanding, then spraying on primer. Once the primer has dried, spray on the right color auto paint. Once dried, wax the repaired area. For detailed instructions on doing this, see: How to Remove Scratches from a Car by Painting. If this is not successful, seek advice from an auto paint repair specialist.
  • Question
    How do you touch up paint on a car with rust?
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer

    Support wikiHow by unlocking this staff-researched answer.

    Be sure it is rust first--rust is usually brown or dark red in color, often flaking and may include tiny holes. The rust must be removed before applying paint otherwise the paint won’t adhere properly and the rust may simply return even if you do manage to paint the surface. You'll find more detailed help here: How to Remove Rust from a Car. Sandpaper off the rust before painting, then use rust-proof primer before adding the appropriate color of auto paint. Severe rust (big holes, pieces of car falling away, etc.) should be attended to by an auto body specialist; painting over it won’t solve the rusting problem.
Advertisement

Warnings

  • Wear safety goggles, gloves, and a paint respirator when applying auto paint and primer.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Car wash and rag
  • Wax remover
  • Rust arrestor
  • Primer
  • Touch-up paint
  • Clear top coat
  • Small brushes
  • Sandpaper: 220, 1000, 2000, and 3000-grit
  • Car polish
  • Car wax

About This Article

Chad Zani
Co-authored by:
Auto Detailing Expert
This article was co-authored by Chad Zani. Chad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide. This article has been viewed 419,108 times.
20 votes - 90%
Co-authors: 12
Updated: August 4, 2021
Views: 419,108
Article SummaryX

To touch up car paint, start by washing the spot on your car that you need to touch up, using a wax and grease remover to remove any residue, and sanding the area with 220-grit sandpaper. Once you've prepped the surface, apply a rust arrestor to the chipped area so rust doesn't spread under your touch-up job. If the chip in the paint reaches the metal underneath, apply a coat of primer as well. Next, paint 2-3 layers over the area, letting the paint dry for 1 hour between each layer. Finally, sand the area and apply a top coat to finish the surface. To learn how to find out the exact paint color on your car, scroll down!

Did this summary help you?
Advertisement