Ethylene oxide

Aqueous solutions of ethylene oxide are rather stable and can exist for a long time without any noticeable chemical reaction, but adding a small amount of acid, such as strongly diluted sulfuric acid, immediately leads to the formation of ethylene glycol, even at room temperature:

(CH₂CH₂)O + H₂O → HO–CH₂CH₂–OH

The reaction also occurs in the gas phase, in the presence of a phosphoric acid salt as a catalyst.[33]

The reaction is usually carried out at about 60 °C (140 °F) with a large excess of water, in order to prevent the reaction of the formed ethylene glycol with ethylene oxide that would form di- and triethylene glycol:[34]

2 (CH₂CH₂)O + H₂O → HO–CH₂CH₂–O–CH₂CH₂–OH

3 (CH₂CH₂)O + H₂O → HO–CH₂CH₂–O–CH₂CH₂–O–CH₂CH₂–OH

The use of alkaline catalysts may lead to the formation of polyethylene glycol:

n (CH₂CH₂)O + H₂O → HO–(–CH₂CH₂–O–)_n–H

Reactions with alcohols proceed similarly yielding ethylene glycol ethers:

(CH₂CH₂)O + C₂H₅OH → HO–CH₂CH₂–OC₂H₅

2 (CH₂CH₂)O + C₂H₅OH → HO–CH₂CH₂–O–CH₂CH₂–OC₂H₅

Reactions with lower alcohols occur less actively than with water and require more severe conditions, such as heating to 160 °C (320 °F) and pressurizing to 3 MPa (440 psi) and adding an acid or alkali catalyst.

Reactions of ethylene oxide with fatty alcohols proceed in the presence of sodium metal, sodium hydroxide or boron trifluoride and are used for the synthesis of surfactants.[33]

Reactions of ethylene oxide with carboxylic acids in the presence of a catalyst results in glycol mono- and diesters:

(CH₂CH₂)O + CH₃CO₂H → HOCH₂CH₂–O₂CCH₃

(CH₂CH₂)O + (CH₃CO)₂O → CH₃CO₂CH₂CH₂O₂CCH₃

The addition of acid amides proceeds similarly:

(CH₂CH₂)O + CH₃CONH₂ → HOCH₂CH₂NHC(O)CH₃

Addition of ethylene oxide to higher carboxylic acids is carried out at elevated temperatures (typically 140–180 °C (284–356 °F)) and pressure (0.3–0.5 MPa (44–73 psi)) in an inert atmosphere, in presence of an alkaline catalyst (concentration 0.01–2%), such as hydroxide or carbonate of sodium or potassium.[35] The carboxylate ion acts as nucleophile in the reaction:

(CH₂CH₂)O + RCO₂⁻ → RCO₂CH₂CH₂O⁻

RCO₂CH₂CH₂O⁻ + RCO₂H → RCO₂CH₂CH₂OH + RCO₂⁻

Ethylene oxide reacts with ammonia forming a mixture of mono-, di- and tri- ethanolamines. The reaction is stimulated by adding a small amount of water.

(CH₂CH₂)O + NH₃ → HO–CH₂CH₂–NH₂

2 (CH₂CH₂)O + NH₃ → (HO–CH₂CH₂)₂NH

3 (CH₂CH₂)O + NH₃ → (HO–CH₂CH₂)₃N

Similarly proceed the reactions with primary and secondary amines:

(CH₂CH₂)O + RNH₂ → HO–CH₂CH₂–NHR

Dialkylamino ethanols can further react with ethylene oxide, forming amino polyethylene glycols:[19]

n (CH₂CH₂)O + R₂NCH₂CH₂OH → R₂NCH₂CH₂O–(–CH₂CH₂O–)_n–H

Trimethylamine reacts with ethylene oxide in the presence of water, forming choline:[36]

(CH₂CH₂)O + (CH₃)₃N + H₂O → [HOCH₂CH₂N (CH₃)₃]⁺OH⁻

Aromatic primary and secondary amines also react with ethylene oxide, forming the corresponding arylamino alcohols.

Ethylene oxide readily reacts with aqueous solutions of hydrochloric, hydrobromic and hydroiodic acids to form halohydrins. The reaction occurs easier with the last two acids:

(CH₂CH₂)O + HCl → HO–CH₂CH₂–Cl

The reaction with these acids competes with the acid-catalyzed hydration of ethylene oxide; therefore, there is always a by-product of ethylene glycol with an admixture of diethylene glycol. For a cleaner product, the reaction is conducted in the gas phase or in an organic solvent.

Ethylene fluorohydrin is obtained differently, by boiling hydrogen fluoride with a 5–6% solution of ethylene oxide in diethyl ether. The ether normally has a water content of 1.5–2%; in absence of water, ethylene oxide polymerizes.[37]

Halohydrins can also be obtained by passing ethylene oxide through aqueous solutions of metal halides:[33]

2 (CH₂CH₂)O + CuCl₂ + 2 H₂O → 2 HO–CH₂CH₂–Cl + Cu(OH)₂↓

Interaction of ethylene oxide with organomagnesium compounds, which are Grignard reagents, can be regarded as nucleophilic substitution influenced by carbanion organometallic compounds. The final product of the reaction is a primary alcohol:

${\displaystyle {\ce {(CH2CH2)O{}+RMgBr->R-CH2CH2-OMgBr->[{\ce {H2O}}]{\overset {primary~alcohol}{R-CH2CH2-OH}}}}}$

Similar mechanism is valid for other organometallic compounds, such as alkyl lithium:

${\displaystyle {\ce {(CH2CH2)O{}+{\overset {alkyl~lithium}{RLi}}->R-CH2CH2-OLi->[{\ce {H2O}}]R-CH2CH2-OH}}}$

Ethylene oxide easily reacts with hydrogen cyanide forming ethylene cyanohydrin:

(CH₂CH₂)O + HCN → HO–CH₂CH₂–CN

A slightly chilled (10–20 °C) aqueous solution of calcium cyanide can be used instead of HCN:[38]

2 (CH₂CH₂)O + Ca(CN)₂ + 2 H₂O → 2 HO–CH₂CH₂–CN + Ca(OH)₂

Ethylene cyanohydrin easily loses water, producing acrylonitrile:

HO–CH₂CH₂–CN → CH₂=CH–CN + H₂O

When reacting with the hydrogen sulfide, ethylene oxide forms 2-mercaptoethanol and thiodiglycol, and with alkylmercaptans it produces 2-alkyl mercaptoetanol:

(CH₂CH₂)O + H₂S → HO–CH₂CH₂–HS

2 (CH₂CH₂)O + H₂S → (HO–CH₂CH₂)₂S

(CH₂CH₂)O + RHS → HO–CH₂CH₂–SR

The excess of ethylene oxide with an aqueous solution of hydrogen sulfide leads to the tris-(hydroxyethyl) sulfonyl hydroxide:

3 (CH₂CH₂)O + H₂S → [(HO–CH₂CH₂)₃S⁺]OH⁻

Reaction of ethylene oxide with aqueous solutions of barium nitrite, calcium nitrite, magnesium nitrite, zinc nitrite or sodium nitrite leads to the formation of 2-nitroethanol:[39]

2 (CH₂CH₂)O + Ca(NO₂)₂ + 2 H₂O → 2 HO–CH₂CH₂–NO₂ + Ca(OH)₂

With nitric acid, ethylene oxide forms mono- and dinitroglycols:[40]

${\displaystyle {\ce {(CH2CH2)O{}+{\overset {nitric \atop acid}{HNO3}}->HO-CH2CH2-ONO2->[{\ce {+HNO3}}][{\ce {-H2O}}]O2NO-CH2CH2-ONO_{2}}}}$

In the presence of alkoxides, reactions of ethylene oxide with compounds containing active methylene group leads to the formation of butyrolactones:[41]

Ethylene oxide enters into the Friedel–Crafts reaction with benzene to form phenethyl alcohol:

Styrene can be obtained in one stage if this reaction is conducted at elevated temperatures (315–440 °C (599–824 °F)) and pressures (0.35–0.7 MPa (51–102 psi)), in presence of an aluminosilicate catalyst.[42]

A series of polynomial heterocyclic compounds, known as crown ethers, can be synthesized with ethylene oxide. One method is the cationic cyclopolymerization of ethylene oxide, limiting the size of the formed cycle:[43]

n (CH₂CH₂)O → (–CH₂CH₂–O–)_n

To suppress the formation of other linear polymers the reaction is carried out in a highly dilute solution.[43]

Reaction of ethylene oxide with sulfur dioxide in the presence of caesium salts leads to the formation of an 11-membered heterocyclic compound which has the complexing properties of crown ethers:[44]

When heated to about 400 °C (750 °F), or to 150–300 °C (300–570 °F) in the presence of a catalyst (Al₂O₃, H₃PO₄, etc.), ethylene oxide isomerizes into acetaldehyde:[45]

${\displaystyle {\ce {(CH2CH2)O->[{\ce {200^{\circ }C}}][{\ce {Al2O3}}]{\overset {acetaldehyde}{CH3CHO}}}}}$

The radical mechanism was proposed to explain this reaction in the gas phase; it comprises the following stages:[46]

(CH2CH2)O ↔ •CH2CH2O• → CH3CHO*

(1)

CH3CHO* → CH3• + CHO•

(2)

CH3CHO* + M → CH3CHO + M*

(3)

In reaction (3), M refers to the wall of the reaction vessel or to a heterogeneous catalyst. The moiety CH₃CHO* represents a short-lived (lifetime of 10^−8.5 seconds), activated molecule of acetaldehyde. Its excess energy is about 355.6 kJ/mol, which exceeds by 29.3 kJ/mol the binding energy of the C-C bond in acetaldehyde.[46]

In absence of a catalyst, the thermal isomerization of ethylene oxide is never selective and apart from acetaldehyde yields significant amount of by-products (see section Thermal decomposition).[47]

Ethylene oxide can be hydrogenated into ethanol in the presence of a catalyst, such as nickel, platinum, palladium,[47] boranes, lithium aluminium hydride and some other hydrides.[48]

${\displaystyle {\ce {(CH2CH2)O{}+H2->[{} \atop {\ce {Ni,Pt,Pd,BH3,LiAlH4}}{\text{ or other hydrides}}][{\ce {80^{\circ }C}}]{\underset {ethanol}{C2H5OH}}}}}$

Conversely, with some other catalysts, ethylene oxide may be reduced by hydrogen to ethylene with the yield up to 70%. The reduction catalysts include mixtures of zinc dust and acetic acid, of lithium aluminium hydride with titanium trichloride (the reducing agent is actually titanium dichloride, formed by the reaction between LiAlH₄ and TiCl₃) and of iron(III) chloride with butyllithium in tetrahydrofuran.[48]

${\displaystyle {\ce {(CH2CH2)O{}+H2->[{} \atop {\ce {{Zn}+CH3COOH}}]{\underset {ethylene}{CH2=CH2}}+H2O}}}$

Ethylene oxide can further be oxidized, depending on the conditions, to glycolic acid or carbon dioxide:

${\displaystyle {\ce {(CH2CH2)O{}+O2->[{\ce {AgNO3}}]{\overset {glycolic\ acid}{HOCH2CO2H}}}}}$

Deep gas-phase reactor oxidation of ethylene oxide at 800–1,000 K (527–727 °C; 980–1,340 °F) and a pressure of 0.1–1 MPa (15–145 psi) yields a complex mixture of products containing O₂, H₂, CO, CO₂, CH₄, C₂H₂, C₂H₄, C₂H₆, C₃H₆, C₃H₈ and CH₃CHO.[49]

In the presence of acid catalysts, ethylene oxide dimerizes to afford dioxane:

The reaction mechanism is as follows:[47]

The dimerization reaction is unselective. By-products include acetaldehyde (due to isomerization). The selectivity and speed of dimerization can be increased by adding a catalyst, such as platinum, platinum-palladium, or iodine with sulfolane. 2-methyl-1,3-dioxolane is formed as a side product in the last case.[50]

Liquid ethylene oxide can form polyethylene glycols. The polymerization can proceed via radical and ionic mechanisms, but only the latter has a wide practical application.[51] Cationic polymerization of ethylene oxide is assisted by protic acids (HClO₄, HCl), Lewis acids (SnCl₄, BF₃, etc.), organometallic compounds, or more complex reagents:[51]

${\displaystyle n{\ce {(CH2CH2)O ->[{\ce {SnCl4}}]}}\ \overbrace {{\ce {(CH2CH2-O-)}}_{n}} ^{{\ce {polyethyleneglycol}}}}$

The reaction mechanism is as follows.[52] At the first stage, the catalyst (MX_m) is initiated by alkyl-or acylhalogen or by compounds with active hydrogen atoms, usually water, alcohol or glycol:

MX_m + ROH → MX_mRO⁻H⁺

The resulting active complex reacts with ethylene oxide via the S_N2 mechanism:

(CH₂CH₂)O + MX_mRO⁻H⁺ → (CH₂CH₂)O•••H⁺O⁻RMX_m

(CH₂CH₂)O•••H⁺ O⁻RMX_m → HO–CH₂CH₂⁺ + MX_mRO⁻₂

HO–CH₂CH₂⁺ + n (CH₂CH₂)O → HO–CH₂CH₂–(O–CH₂CH₂)_n⁺

The chain breaks as

HO–CH₂CH₂–(O–CH₂CH₂)_n⁺ + MX_mRO⁻ → HO–CH₂CH₂–(O–CH₂CH₂)_n–OR + MX_m

H(O–CH₂CH₂)_n–O–CH₂–CH₂⁺ + MX_mRO⁻ → H(O–CH₂CH₂)_n–O–CH=CH₂ + MX_m + ROH

Anionic polymerization of ethylene oxide is assisted by bases, such as alkoxides, hydroxides, carbonates or other compounds of alkali or alkaline earth metals.[51] The reaction mechanism is as follows:[52]

(CH₂CH₂)O + RONa → RO–CH₂CH₂–O⁻Na⁺

RO–CH₂CH₂–O⁻Na⁺ + n (CH₂CH₂)O → RO–(CH₂CH₂–O)_n–CH₂CH₂–O⁻Na⁺

RO–(CH₂CH₂–O)_n–CH₂CH₂–O⁻Na⁺ → RO–(CH₂CH₂–O)_n–CH=CH₂ + NaOH

RO–(CH₂CH₂–O)_n–CH₂CH₂–O⁻Na⁺ + H₂O → RO–(CH₂CH₂–O)_(n+1)OH + NaOH

Ethylene oxide is relatively stable to heating – in the absence of a catalyst, it does not dissociate up to 300 °C (572 °F), and only above 570 °C (1,058 °F) there is a major exothermic decomposition, which proceeds through the radical mechanism.[47] The first stage involves isomerization, however high temperature accelerates the radical processes. They result in a gas mixture containing acetaldehyde, ethane, ethyl, methane, hydrogen, carbon dioxide, ketene and formaldehyde.[53] High-temperature pyrolysis (830–1,200 K (557–927 °C; 1,034–1,700 °F)) at elevated pressure in an inert atmosphere leads to a more complex composition of the gas mixture, which also contains acetylene and propane.[54] Contrary to the isomerization, initiation of the chain occurs mainly as follows:[54]

(CH₂CH₂)O → •CH₂CH₂O• → CH₂O + CH₂:

When carrying the thermal decomposition of ethylene oxide in the presence of transition metal compounds as catalysts, it is possible not only to reduce its temperature, but also to have ethyl as the main product, that is to reverse the ethylene oxide synthesis reaction.

Thiocyanate ions or thiourea transform ethylene oxide into thiirane (ethylene sulfide):[55]

(CH₂CH₂)O + (NH₂)₂C=S → (CH₂CH₂)S + (NH₂)₂C=O

Reaction of phosphorus pentachloride with ethylene oxide produces ethylene dichloride:[33]

(CH₂CH₂)O + PCl₅ → Cl–CH₂CH₂–Cl + POCl₃

Other dichloro derivatives of ethylene oxide can be obtained by combined action of sulfuryl chloride (SOCl₂) and pyridine and of triphenylphosphine and carbon tetrachloride.[56]

Phosphorus trichloride reacts with ethylene oxide forming chloroethyl esters of phosphorous acid:[33]

(CH₂CH₂)O + PCl₃ → Cl–CH₂CH₂–OPCl₂

2 (CH₂CH₂)O + PCl₃ → (Cl–CH₂CH₂–O)₂PCl

3 (CH₂CH₂)O + PCl₃ → Cl–CH₂CH₂–O)₃P

The reaction product of ethylene oxide with acyl chlorides in the presence of sodium iodide is a complex iodoethyl ester:[56]

(CH₂CH₂)O + RCOCl + NaI → RC(O)–OCH₂CH₂–I + NaCl

Heating ethylene oxide to 100 °C with carbon dioxide, in a non-polar solvent in the presence of bis-(triphenylphosphine)-nickel(0) results in ethylene carbonate:[57]

In industry, a similar reaction is carried out at high pressure and temperature in the presence of quaternary ammonium or phosphonium salts as a catalyst.[58]

Reaction of ethylene oxide with formaldehyde at 80–150 °C in the presence of a catalyst leads to the formation of 1,3-dioxolane:[59]

Substituting formaldehyde by other aldehydes or ketones results in a 2-substituted 1,3-dioxolane (yield: 70–85%, catalyst: tetraethylammonium bromide).[59]

Catalytic hydroformylation of ethylene oxide gives hydroxypropanal which can be hydrogenated to propane-1,3-diol:[60]

${\displaystyle {\ce {(CH2CH2)O + CO + H2 -> CHO-CH2CH2-OH ->[{\ce {+H2}}] HO-CH2CH2CH2-OH}}}$

Dehydrochlorination of 2-chloroethanol, developed by Wurtz in 1859, remains a common laboratory route to ethylene oxide:

${\displaystyle {\ce {Cl-CH2CH2-OH + NaOH -> (CH2CH2)O + NaCl + H2O}}}$

The reaction is carried out at elevated temperature, and beside sodium hydroxide or potassium hydroxide, calcium hydroxide, barium hydroxide, magnesium hydroxide or carbonates of alkali or alkaline earth metals can be used.[61]

With a high yield (90%) ethylene oxide can be produced by treating calcium oxide with ethyl hypochlorite; substituting calcium by other alkaline earth metals reduces the reaction yield:[62]

${\displaystyle {\ce {2 CH3CH2-OCl + CaO -> 2 (CH2CH2)O + CaCl2 + H2O}}}$

Ethylene can be directly oxidized into ethylene oxide using peroxy acids, for example, peroxybenzoic or meta-chloro-peroxybenzoic acid:[63]

Oxidation by peroxy acids is efficient for higher alkenes, but not for ethylene. The above reaction is slow and has low yield, therefore it is not used in the industry.[62]

Other synthesis methods include[62] reaction of diiodo ethane with silver oxide:

${\displaystyle {\ce {I-CH2CH2-I + Ag2O -> (CH2CH2)O + 2AgI}}}$

and decomposition of ethylene carbonate at 200–210 °C (392–410 °F) in the presence of hexachloroethane:

Commercial production of ethylene oxide dates back to 1914 when BASF built the first factory which used the chlorohydrin process (reaction of ethylene chlorohydrin with calcium hydroxide). The chlorohydrin process was unattractive for several reasons, including low efficiency and loss of valuable chlorine into calcium chloride.[64] More efficient direct oxidation of ethylene by air was invented by Lefort in 1931 and in 1937 Union Carbide opened the first plant using this process. It was further improved in 1958 by Shell Oil Co. by replacing air with oxygen and using elevated temperature of 200–300 °C (390–570 °F) and pressure (1–3 MPa (150–440 psi)).[65] This more efficient routine accounted for about half of ethylene oxide production in the 1950s in the US, and after 1975 it completely replaced the previous methods.[65] The production of ethylene oxide accounts for approximately 11% of worldwide ethylene demand.[66]

Although the chlorohydrin process is almost entirely superseded in the industry by the direct oxidation of ethylene, the knowledge of this method is still important for educational reasons and because it is still used in the production of propylene oxide.[67] The process consists of three major steps: synthesis of ethylene chlorohydrin, dehydrochlorination of ethylene chlorohydrin to ethylene oxide and purification of ethylene oxide. Those steps are carried continuously. In the first column, hypochlorination of ethylene is carried out as follows:[68]

Cl₂ + H₂O → HOCl + HCl

CH₂=CH₂ + HOCl → HO–CH₂CH₂–Cl

CH₂=CH₂ + Cl₂ → Cl–CH₂CH₂–Cl

To suppress the conversion of ethylene into the ethylene dichloride (the last reaction), the concentration of ethylene is maintained at about 4–6%, and the solution is heated by steam to the boiling point.[68]

Next, aqueous solution of ethylene chlorohydrin enters the second column, where it reacts with a 30% solution of calcium hydroxide at 100 °C (212 °F):[68]

2 HO–CH₂CH₂–Cl + Ca(OH)₂ → 2 (CH₂CH₂)O + CaCl₂ + 2H₂O

The produced ethylene oxide is purified by rectification. The chlorohydrin process allows to reach 95% conversion of ethylene chlorohydrin. The yield of ethylene oxide is about 80% of the theoretical value; for 1 tonne (0.98 long tons; 1.1 short tons) of ethylene oxide, about 200 kg (440 lb) of ethylene dichloride is produced.[68] But, the major drawbacks of this process are high chlorine consumption and effluent load. This process is now obsolete.

Direct oxidation of ethylene was patented by Lefort in 1931. This method was repeatedly modified for industrial use, and at least four major variations are known. They all use oxidation by oxygen or air and a silver-based catalyst, but differ in the technological details and hardware implementations.[69]

Union Carbide (currently a division of Dow Chemical Company) was the first company to develop the direct oxidation process.[70]

A similar production method was developed by Scientific Design Co., but it received wider use because of the licensing system – it accounts for 25% of the world's production and for 75% of world's licensed production of ethylene oxide.[70][71] A proprietary variation of this method is used by Japan Catalytic Chemical Co., which adapted synthesis of both ethylene oxide and ethylene glycol in a single industrial complex.

A different modification was developed Shell International Chemicals BV. Their method is rather flexible with regard to the specific requirements of specific industries; it is characterized by high selectivity with respect to the ethylene oxide product and long lifetime of the catalyst (3 years). It accounts for about 40% of global production.[70]

Older factories typically use air for oxidation whereas newer plants and processes, such as METEOR and Japan Catalytic, favor oxygen.[72]

Formally, the direct oxidation process is expressed by the following equation:

${\displaystyle {\ce {2CH_2=CH2 + O2 ->[{\ce {Ag}}] 2(CH2CH2)O}}}$, ΔH = −105 kJ/mol

However, significant yield of carbon dioxide and water is observed in practice, which can be explained by the complete oxidation of ethylene or ethylene oxide:

CH₂=CH₂ + 3 O₂ → 2 CO₂ + 2 H₂O, ΔH = −1327 kJ/mol

(CH₂CH₂)O + 2.5 O₂ → 2 CO₂ + 2 H₂O, ΔH = −1223 kJ/mol

According to a kinetic analysis by Kilty and Sachtler, the following reactions describe the pathway leading to EO. In the first step, a superoxide (O₂⁻) species is formed:[73]

O₂ + Ag → Ag⁺O₂⁻

This species reacts with ethylene

Ag⁺O₂⁻ + H₂C=CH₂ → (CH₂CH₂)O + AgO

The resulting silver oxide then oxidizes ethylene or ethylene oxide to CO₂ and water. This reaction replenishes the silver catalyst. Thus the overall reaction is expressed as

7 CH₂=CH₂ + 6 O₂ → 6 (CH₂CH₂)O + 2 CO₂ + 2 H₂O

and the maximum degree of conversion of ethylene to ethylene oxide is theoretically predicted to be 6/7 or 85.7%,[73] although higher yields are achieved in practice.[74]

The catalyst for the reaction is metallic silver deposited on various matrixes, including pumice, silica gel, various silicates and aluminosilicates, alumina and silicon carbide, and activated by certain additives (antimony, bismuth, barium peroxide, etc.).[75] The process temperature was optimized as 220–280 °C (430–540 °F). Lower temperatures reduce the activity of the catalyst, and higher temperatures promote the complete oxidation of ethylene thereby reducing the yield of ethylene oxide. Elevated pressure of 1–3 MPa (150–440 psi) increases the productivity of the catalyst and facilitates absorption of ethylene oxide from the reacting gases.[75]

Whereas oxidation by air is still being used, oxygen (> 95% purity) is preferred for several reasons, such as higher molar yield of ethylene oxide (75–82% for oxygen vs. 63–75% for air), higher reaction rate (no gas dilution) and no need of separating nitrogen in the reaction products.[19][76]

The production of ethylene oxide on a commercial scale is attained with the unification of the following unit processes:

• Main reactor
• Ethylene oxide scrubber
• Ethylene oxide de-sorber
• Stripping and distillation column
• CO₂ scrubber and CO₂ de-scrubber

Main Reactor: The main reactor consists of thousands of catalyst tubes in bundles. These tubes are generally 6 to 15 m (20 to 50 ft) long with an inner diameter of 20 to 50 mm (0.8 to 2.0 in). The catalyst packed in these tubes is in the form of spheres or rings of diameter 3 to 10 mm (0.12 to 0.39 in). The operating conditions of 200–300 °C (390–570 °F) with a pressure of 1–3 MPa (150–440 psi) prevail in the reactor. To maintain this temperature, the cooling system of the reactor plays a vital role. With the aging of the catalyst, its selectivity decreases and it produces more exothermic side products of CO₂.

Ethylene oxide scrubber: After the gaseous stream from the main reactor, containing ethylene oxide (1–2%) and CO₂ (5%), is cooled, it is then passed to the ethylene oxide scrubber. Here, water is used as the scrubbing media which scrubs away majority of ethylene oxide along with some amounts of CO₂, N₂, CH₂=CH₂, CH₄ and aldehydes (introduced by the recycle stream). Also, a small proportion of the gas leaving the ethylene oxide scrubber (0.1–0.2%) is removed continuously (combusted) to prevent the buildup of inert compounds (N₂, Ar, and C₂H₆), which are introduced as impurities with the reactants.

Ethylene oxide de-sorber: The aqueous stream resulting from the above scrubbing process is then sent to the ethylene oxide de-sorber. Here, ethylene oxide is obtained as the overhead product, whereas the bottom product obtained is known as the glycol bleed. When ethylene oxide is scrubbed from the recycle gas with an aqueous solution, ethylene glycols (viz. mono-ethylene glycol, di-ethylene glycol and other poly-ethylene glycols) get unavoidably produced. Thus, in-order to prevent them from building up in the system, they are continuously bled off.

Stripping and distillation column: Here, the ethylene oxide stream is stripped off its low boiling components and then distilled in-order to separate it into water and ethylene oxide.

CO₂ scrubber: The recycle stream obtained from the ethylene oxide scrubber is compressed and a side-stream is fed to the CO₂ scrubber. Here, CO₂ gets dissolved into the hot aqueous solution of potassium carbonate (i.e., the scrubbing media). The dissolution of CO₂ is not only a physical phenomenon, but a chemical phenomenon as well, for, the CO₂ reacts with potassium carbonate to produce potassium hydrogen carbonate.

K₂CO₃ + CO₂ + H₂O → 2 KHCO₃

CO₂ de-scrubber: The above potassium carbonate solution (enriched with CO₂) is then sent to the CO₂ de-scrubber where CO₂ is de-scrubbed by stepwise (usually two steps) flashing. The first step is done to remove the hydrocarbon gases, and the second step is employed to strip off CO₂.

The world production of ethylene oxide was 20 Mt (22 million short tons) in 2009,[77] 19 Mt (21 million short tons) in 2008 and 18 Mt (20 million short tons) in 2007.[78] This places ethylene oxide 14th most produced organic chemical, whereas the most produced one was ethylene with 113 Mt (125 million short tons).[79] SRI Consulting forecasted the growth of consumption of ethylene oxide of 4.4% per year during 2008–2013 and 3% from 2013 to 2018.[78]

In 2004, the global production of ethylene oxide by region was as follows:[80]

The world's largest producers of ethylene oxide are Dow Chemical Company (3–3.5 Mt (3.3–3.9 million short tons) in 2006[81]), Saudi Basic Industries (2,000–2,500 tonnes (2,200–2,800 short tons) in 2006[81]), Royal Dutch Shell (1.328 Mt (1.464 million short tons) in 2008–2009[82][83][84]), BASF (1.175 Mt (1.295 million short tons) in 2008–2009[85]), China Petrochemical Corporation (~1 Mt (1.1 million short tons) in 2006[81]), Formosa Plastics (~1 Mt (1.1 million short tons) in 2006[81]) and Ineos (0.92 Mt (1.01 million short tons) in 2008–2009).[86]

Ethylene glycol is industrially produced by non-catalytic hydration of ethylene oxide at a temperature of 200 °C (392 °F) and a pressure of 1.5–2 MPa (220–290 psi):[89]

${\displaystyle {\ce {(CH2CH2)O + H2O -> HOCH2CH2OH}}}$

By-products of the reaction are diethylene glycol, triethylene glycol and polyglycols with the total of about 10%, which are separated from the ethylene glycol by distillation at reduced pressure.[90]

Another synthesis method is the reaction of ethylene oxide and CO2 (temperature 80–120 °C (176–248 °F) and pressure of 5.2 MPa (750 psi)) yielding ethylene carbonate and its subsequent hydrolysis with decarboxylation:[89]

${\displaystyle {\ce {(CH2CH2)O{}+CO2->{\overset {ethylene\ carbonate}{(O-CH2CH_{2}-O)C=O}}->[{\ce {+H2O}}][{\ce {-CO2}}]HOCH2CH2OH}}}$

Modern technologies of production of ethylene glycol include the following.[91] Shell OMEGA technology (Only Mono-Ethylene Glycol Advantage) is a two-step synthesis of ethylene carbonate using a phosphonium halide as a catalyst. The glycol yield is 99–99.5%, with other glycols practically absent. The main advantage of the process is production of pure ethylene glycol without the need for further purification. The first commercial plant which uses this method was opened in 2008 in South Korea.[92] Dow METEOR (Most Effective Technology for Ethylene Oxide Reactions) is an integrated technology for producing ethylene oxide and its subsequent hydrolysis into ethylene glycol. The glycol yield is 90–93%. The main advantage of the process is relative simplicity, using fewer stages and less equipment.

Conversion to ethylene glycol is also the means by which waste ethylene oxide is scrubbed before venting to the environment. Typically the EtO is passed over a matrix containing either sulfuric acid or potassium permanganate.

The major industrial esters of mono-, di- and triethylene glycols are methyl, ethyl and normal butyl ethers, as well as their acetates and phthalates. The synthesis involves reaction of the appropriate alcohol with ethylene oxide:[93]

${\displaystyle {\ce {(CH2CH2)O + ROH -> HOCH2CH2OR}}}$

${\displaystyle {\ce {(CH2CH2)O + HOCH2CH2OR -> HOCH2CH2OCH2CH2OR}}}$

${\displaystyle {\ce {(CH2CH2)O + HOCH2CH2OCH2CH2OR -> HOCH2CH2OCH2CH2OCH2CH2OR}}}$

The reaction of monoesters with an acid or its anhydride leads to the formation of the esters:

${\displaystyle {\ce {CH3CO2H + HOCH2CH2OR -> ROCH2CH2OCOCH3 + H2O}}}$

In the industry, ethanolamines (mono-, di- and triethanolamines) are produced by reacting ammonia and ethylene oxide in anhydrous medium at a temperature of 40–70 °C (100–160 °F) and pressure of 1.5–3.5 MPa (220–510 psi) MPa:[94]

${\displaystyle {\ce {(CH2CH2)O + NH3 -> HOCH2CH2NH2}}}$

${\displaystyle {\ce {2 (CH2CH2)O + NH3 -> (HOCH2CH2)2NH}}}$

${\displaystyle {\ce {3 (CH2CH2)O + NH3 -> (HOCH2CH2)3N}}}$

All three ethanolamines are produced in the process, while ammonia and part of methylamine are recycled. The final products are separated by vacuum distillation. Hydroxyalkylamines are produced in a similar process:

${\displaystyle {\ce {(CH2CH2)O + RNH2 -> HOCH2CH2NHR}}}$

${\displaystyle {\ce {2 (CH2CH2)O + RNH2 -> (HOCH2CH2)2NR}}}$

Monosubstituted products are formed by reacting a large excess of amine with ethylene oxide in presence of water and at a temperature below 100 °C (212 °F). Disubstituted products are obtained with a small excess of ethylene oxide, at a temperature of 120–140 °C (250–280 °F) and a pressure of 0.3–0.5 MPa (45–75 psi).[95][96]

Industrial production of ethoxylates is realized by a direct reaction of higher alcohols, acids or amines with ethylene oxide in the presence of an alkaline catalyst at a temperature of 120–180 °C (250–360 °F). Modern plants producing ethoxylates are usually based on the BUSS LOOP reactors technology,[97] which is based on a three-stage continuous process. In the first stage, the initiator or catalyst of the reaction and the feedstock are fed into the container, where they are mixed, heated and vacuum dried. Then reaction is carried out in a special insulated reactor in an inert atmosphere (nitrogen) to prevent a possible explosion of ethylene oxide. Finally, the reaction mixture is neutralized, degassed and purified.[98]

Currently, most acrylonitrile (90% in 2008) is produced by the SOHIO method, which is based on the catalytic oxidation of propylene in the presence of ammonia and bismuth phosphomolybdate. However, until 1960 a key production process was addition of hydrogen cyanide to ethylene oxide, followed by dehydration of the resulting cyanohydrin:[99] [100]

${\displaystyle {\ce {(CH2CH2)O + HCN -> HOCH2CH2CN ->[][{\ce {-H2O}}] CH2=CH-CN}}}$

Addition of hydrocyanic acid to ethylene oxide is carried out in the presence of a catalyst (sodium hydroxide and diethylamine), and dehydration of cyanohydrin occurs in the gas phase upon the catalytic action of aluminium oxide.[101]

Ethylene oxide is one of the most commonly used sterilization methods in the healthcare industry because of its non-damaging effects for delicate instruments and devices that require sterilization, and for its wide range of material compatibility.[103] It is used for instruments that cannot tolerate heat, moisture or abrasive chemicals, such as electronics, optical equipment, paper, rubber and plastics.[104] It was developed in the 1940s as a sterilant by the US military, and its use as a medical sterilant dates to the late 1950s, when the McDonald process was patented for medical devices.[105] The Anprolene system was patented in the 1960s[106] by Andersen Products,[107] and it remains the most commonly used system in several niche markets, notably the veterinary market and some international markets.[108] It relies on the use of a flexible sterilization chamber and an EtO cartridge for small volume sterilization, and where environmental and/or portability considerations dictate the use of a low dose. It is therefore referred to as the "flexible chamber sterilization" method, or the "gas diffusion sterilization" method.

In the United States, the operation of EtO sterilization is overseen by the EPA through the National Emissions Standards for Hazardous Air Pollutants (NESHAP).[109]

Ethylene oxide is used as a fungicide and as an accelerator of maturation of tobacco leaves.[102] Ethylene oxide is also used as a main component of thermobaric weapons (fuel-air explosives).[12][13][110]

On 14 January 2020 in an industrial estate near Tarragona, an explosion of an ethoxylation reactor owned by the chemical company Industrias Quimicas de Oxido de Etileno (IQOXE, part of the CL Industrial Group) occurred.[119][120] The accident launched substantial debris over a radius of about two and a half kilometers, one piece penetrating a distant home and killing an occupant.[121] It is reported that at least three people were killed and seven injured as a direct result of the explosion.[122]

The company was, until the time of the explosion the only producer of ethylene oxide in Spain with an installed capacity of 140,000 tons/year. Half of that production was used to manufacture ethylene glycol for PET production.[123] The accident will be investigated under EU regulations within the context of the European Agency for Safety and Health at Work.

In September 2020, high levels of pesticides were found in 268 tonnes of sesame seeds from India. The contamination had a level of 1000 to 3500 times the limit of 0.05 milligrams per kilogram for ethylene oxide allowed in Europe. This pesticide is forbidden in Europe, it is known to be carcinogenic and mutagenic. A product recall was made, half of the products had an organic certification.[124][125]

In September, alert was raised by Belgium by RASFF, but the product has also been sold in other EU single market countries such as France[126] and Ireland.

Exposure to ethylene oxide gas causes alkylation to microorganisms at a nuclear level.[127] The disinfectant effect of ethylene oxide is similar to that of sterilization by heat, but because of limited penetration, it affects only the surface. ETO sterilization can take up to 12 hours due to its slow action upon microorganisms, and lengthy processing and aeration time.[128]

Ethylene oxide is an alkylating agent; it has irritating, sensitizing and narcotic effects.[129] Chronic exposure to ethylene oxide is also mutagenic. The International Agency for Research on Cancer classifies ethylene oxide into group 1, meaning it is a proven carcinogen.[130][131] Ethylene oxide is classified as a class 2 carcinogen by the German MAK commission and as a class A2 carcinogen by the ACGIH. A 2003 study of 7,576 women exposed while at work in commercial sterilization facilities in the US suggests ethylene oxide is associated with breast cancer incidence.[132] A 2004 follow up study analyzing 18,235 men and women workers exposed to ethylene oxide from 1987 to 1998 concluded "There was little evidence of any excess cancer mortality for the cohort as a whole, with the exception of bone cancer based on small numbers. Positive exposure-response trends for lymphoid tumors were found for males only. Reasons for the sex specificity of this effect are not known. There was also some evidence of a positive exposure-response for breast cancer mortality."[133] An increased incidence of brain tumors and mononuclear cell leukemia was found in rats that had inhaled ethylene oxide at concentrations of 10, 33 or 100 mL/m³ (0.0100, 0.0329 or 0.0997 imp fl oz/cu ft) over a period of two years.[134] An increased incidence of peritoneal mesotheliomas was also observed in the animals exposed to concentrations of 33 and 100 mL/m³ (0.0329 and 0.0997 imp fl oz/cu ft). Results of human epidemiological studies on workers exposed to ethylene oxide differ. There is evidence from both human and animal studies that inhalation exposure to ethylene oxide can result in a wide range of carcinogenic effects.

Ethylene oxide is toxic by inhalation, with a US OSHA permissible exposure limit calculated as a TWA (time weighted average) over 8 hours of 1 ppm, and a short term exposure limit (excursion limit) calculated as a TWA over 15 minutes of 5 ppm.[135] At concentrations in the air about 200 parts per million, ethylene oxide irritates mucous membranes of the nose and throat; higher contents cause damage to the trachea and bronchi, progressing into the partial collapse of the lungs. High concentrations can cause pulmonary edema and damage the cardiovascular system; the damaging effect of ethylene oxide may occur only after 72 hours after exposure.[26] The maximum content of ethylene oxide in the air according to the US standards (ACGIH) is 1.8 mg/m³ (0.00079 gr/cu ft).[136] NIOSH has determined that the Immediately Dangerous to Life and Health level (IDLH) is 800 ppm.[137]

Because the odor threshold for ethylene oxide varies between 250 and 700 ppm, the gas is already at toxic concentrations when it can be smelled. Even then, the odor of ethylene oxide is sweet and aromatic and can easily be mistaken for the aroma of diethyl ether, a common laboratory solvent of very low toxicity. In view of these insidious properties, continuous electrochemical monitoring is standard practice, and it is forbidden to use ethylene oxide to fumigate building interiors in the EU and some other jurisdictions.[138]

Ethylene oxide causes acute poisoning, accompanied by a variety of symptoms.[129] Central nervous system effects are frequently associated with human exposure to ethylene oxide in occupational settings. Headache, nausea, and vomiting have been reported. Peripheral neuropathy, impaired hand-eye coordination and memory loss have been reported in more recent case studies of chronically-exposed workers at estimated average exposure levels as low as 3 ppm (with possible short-term peaks as high as 700 ppm).[134] The metabolism of ethylene oxide is not completely known. Data from animal studies indicate two possible pathways for the metabolism of ethylene oxide: hydrolysis to ethylene glycol and glutathione conjugation to form mercapturic acid and meththio-metabolites.

Ethylene oxide easily penetrates through ordinary clothing and footwear, causing skin irritation and dermatitis with the formation of blisters, fever and leukocytosis.[129]

Toxicity data for ethylene oxide are as follows:[135]

• Eye exposure: 18 mg (0.28 gr)/6 hours (rabbit)
• Oral: 72 mg/kg (0.00115 oz/lb) (rat, LD₅₀), 1,186 mg/kg (0.01898 oz/lb) (rat, TD_Lo), 5,112 mg/kg (0.08179 oz/lb) (rat, TD)
• Inhalation: 12,500 ppm (human, TC_Lo), 960 ppm/4 hours (dog, LC₅₀) 33–50 ppm (rat or mouse, TC), 800 ppm/4 hours (rat or mouse, LC₅₀)
• Subcutaneous injection: 100 mg/kg (0.0016 oz/lb) (cat, LD_Lo), 292 mg/kg (0.00467 oz/lb) (mouse, TD_Lo) 900–2,600 mg/kg (0.014–0.042 oz/lb) (mouse, TD), 187 mg/kg (0.00299 oz/lb) (rat, LD₅₀).
• Intraperitoneal injection: 750 mg/kg (0.0120 oz/lb) (mouse, TD_Lo), 175 mg/kg (0.00280 oz/lb) (mouse, LD₅₀)
• Intravenous injection: 175 mg/kg (0.00280 oz/lb) (rabbit, LD₅₀), 290 mg/kg (0.0046 oz/lb) (mouse, LD₅₀)
• The US Environmental Protection Agency (USEPA) estimated in 2016[139] that for low doses, the inhalation of ethylene oxide for a lifetime could increase an individual's lifetime cancer risk by as much as 3.0 × 10⁻³ per μg/m³ (without considering that early-life exposures are likely more potent). The USEPA estimated the slope of the dose-response declines at higher doses, and extra cancer risk estimates for several occupational exposure scenarios are calculated.