Install coaxial (coax) cable between your DirecTV (DTV) dish and receivers the way you want it to run. Add an old receiver to the system without incurring installation labor costs by doing it yourself.

1

Get some coaxial cable.

  1. The quality and length of cable depends on your devices. Select a quality "RG6" (or "RG6 Quad Shield" for longer runs) coaxial cable for installation between the dish and each tuner.
    • Although there are different coaxial cable sizes, RG6 is usually the most commonly found in residential applications.
    • Since most Direct TV (DTV) DVRs and TiVOs have dual tuners, consider running two cables instead of just one.
    • In the case of the DTV High Definition DVR or DTV High Definition TiVO, consider three cables if you wish to connect an "off air" antenna to receive local channels that are not available from DTV.
    • If DVRs are not planned, installing one cable will supply a simple DTV receiver.
  2. Advertisement
3

Install a grounding wire.

  1. Install a #10 copper wire between the house ground point and the grounding terminal screw of the new ground block. The house ground point can be a ground rod, electric meter, or similar. These two points must be connected together.
    • Use a clamp designed for the purpose to connect the #10 wire to the house's ground point.
    • Do not under any circumstances disconnect or loosen existing ground connections to install the new #10 wire.
    • Leave enough ground wire to "thread" through each ground block(s) ground terminal.
    • Route the cable and secure with staples to the mounting surface.
    • Securely tighten the ground terminal screw to the ground wire.
  2. Advertisement
7

Select a multiswitch.

  1. Choose a multiswitch by determining how many inputs and outputs are needed. The number of inputs equals the number of LNBs on the dish plus one. A dual LNB dish would require a three input multiswitch. The extra input is to mix in an "off air" antenna or CATV signal. The number of outputs of the multiswitch equals the number of tuners (not the number of receivers or set top boxes) in your system.
    • A system of three set top boxes consisting of two DTV receivers and a DTV DVR or TiVO with two tuners would require a four output multiswitch. Of course, if you add another receiver later, you'll need a multiswitch that has additional outputs. Try to buy a multiswitch with enough extra outputs to allow your system to "grow".
    • Cascadable multiswitches can be installed "down line" from other multiswitches, but must be identified for that use.
    • Multiswitches become more expensive as the number of inputs and outputs increase. DTV will install as many as needed free of charge when they add or change equipment such as receivers or antennas. It's best to let DTV do this, but there is no reason why you can't if the cost is not an issue.
  2. Advertisement
9

Connect the receiver to the tuner.

  1. At the receiver end, connect coax cables(s) to each tuner input(s). The satellite cables connect to the satellite inputs - it does not matter which one. If you ran only one satellite cable, connect it to satellite input 1.
    • If this is a location that will need an off air antenna input as well, instead of connecting a cable directly into the tuner, connect it to a "diplexer" input instead. The diplexer will have a diagram indicating satellite and UHF/VHF connections. The diplexer "satellite out" connects to the DTV receiver tuner, and the UHF/VHF can connect to the "antenna" or "CATV" input of the DTV set top box OR even an FM Stereo receiver.
  2. Advertisement

Community Q&A

  • Question
    Do I just run two coax cables from my TVs to the dish to set it up?
    Community Answer
    Community Answer
    Yes.
  • Question
    How do I connect coax wires with red, white, yellow?
    Community Answer
    Community Answer
    You can use an RF modulator (available anywhere home electronics are sold) to go from composite video (YELLOW) and left (WHITE) and right (RED) audio to coax to TV. It should work on either Channel 3 or 4.
  • Question
    Where can I buy a cable cord when I want to move the TV to a different location in the house?
    Community Answer
    Community Answer
    Most department, hardware, or electronics stores will sell coax cables in different sizes (Lowe's, Home Depot, Target, Walmart, Best Buy, etc.).
Advertisement

Warnings

  • Locate the multiswitch near a 120 volt outlet, as some require power for internal amplifiers.
    ⧼thumbs_response⧽
  • NEVER install "splitters" on satellite feed coax cables. Multiswitches are the satellite equivalent of CATV "splitters" and are not interchangeable.
    ⧼thumbs_response⧽
  • DESq switches are a multiswitch for use on Dish Network satellite systems. They are incompatible with a Direct TV system and must not be used.
    ⧼thumbs_response⧽
  • Install only one diplexer on a cable after a multiswitch. 2 or more diplexers on the same cable will result in degraded signals.
    ⧼thumbs_response⧽
  • Do not use RG59 cable. It lacks the bandwidth for today's satellite and CATV system requirements. Use only RG6 if run less than 100 feet (30.5 m). RG6QS cable is suitable for all installations, and required for runs greater than 100 feet (30.5 m) in length.
    ⧼thumbs_response⧽
  • This article is about installing cables for a non "SWM" Direct TV system. While many of the steps are applicable to a Dish Network or Cable TV installation, there are some important differences, so this wiki should not be used as a guide for installing those systems.
    ⧼thumbs_response⧽
Advertisement

About This Article

James Hornof
Co-authored by:
Master Electrician
This article was co-authored by James Hornof. James Hornof is a Master Electrician and the Owner and President of B & W Electric based in Denver, Colorado. With over two decades of experience in the electrical construction industry, James specializes in field installation, management, estimating, and design. He graduated top of his class in electrical trade school and studied Business Management at The Community College of Denver. James holds a Master Electrician license in Colorado, Wyoming, and Texas. This article has been viewed 406,992 times.
How helpful is this?
Co-authors: 17
Updated: March 22, 2023
Views: 406,992
Categories: Satellite Television
Advertisement