Kitchen curtains add a decorative touch to the over-the-sink picture windows commonly found in many kitchens. Because they are located in an area where they might possibly be exposed to moisture, heat and flame, kitchen window treatments require special design considerations. Their location places certain restrictions on their fabric, length and bulk, making kitchen curtains less complex to create than the more ornate window treatments used in living areas. You do not need to be a seamstress to sew curtains for your kitchen. Just follow these steps for how to make kitchen curtains.

Steps

  1. 1
    Determine the type of window treatment you want. You have a few choices when it comes to kitchen window treatments.
    • Curtains. These are 2 gathered panels that hang from top to bottom, framing the window on both the left and right sides.
    • Valances. A valance is a panel that spans horizontally over the only the upper portion of the window, leaving the lower part of the window undressed.
    • Privacy tiers. Tiers are single-panel window treatments designed to block only the lower 1/2 or 2/3 of the window. They are often used in combination with a valance.
  2. 2
    Measure your window. Record the measurements for your window's length and width. If you want to create a privacy tier, also measure the distance from the vertical center-point to the bottom of the window.[1]
    Advertisement
  3. 3
    Decide on the fullness for your kitchen window treatments. This will determine how much fabric you need to purchase. Generally speaking, the fuller the curtain, the more opulent it feels. A fullness of 1 1/2 equates to a flat panel and a fullness of 3 is a luxuriously gathered panel.
  4. 4
    Determine the amount of fabric you will need. Follow these guidelines to calculate the yardage of fabric that you will need.[2]
    • Multiply your fullness (1 1/2 to 3) by the width of your window. For example, if your window is 2 foot (0.6 m), then you will need a 4 foot (1.2 m) length of fabric for each full-sized panel you intend to create.
    • Remember that a valance and a privacy tier are each one full-sized panel.
    • If you are planning to sew curtains, your panel length will be 1/2 of the full-sized panel length and you will need 2 panels per window.
    • Add at least 2 inches (5 cm) to the width and 6 inches (15 cm) to the length of your valance, tier or curtain design to account for seams, rod pockets and hems. You may adjust that number, depending on your design and the size of your rod.
  5. 5
    Choose a fabric. When you make kitchen curtains, you must keep in mind the practicality factor. You should not use any fabric that will shrink or fade easily, or that cannot be washed. It is also a good idea to choose a flame-retardant fabric, just in case of cooking mishap.[3]
  6. 6
    Lay fabric out and iron it on a flat surface.
  7. 7
    Use a measuring tape and straight edge to outline the dimensions of your panels on the fabric with a fabric marker.
  8. 8
    Cut out your panels.
  9. 9
    Create the lower hem.[4]
    • Fold the lower edge of your panel up 0.5 inch (1.25 cm), wrong side in, and press.
    • Fold the clean edge up, facing the wrong side of the fabric, to the desired hem amount (keeping in mind the amount you allotted when you cut your panel) and press again.
    • Stitch the top folded edge of the hem to secure it in place.
  10. 10
    Finish the right and left rough edges.
    • Fold the vertical edges 0.5 inch (1.25 cm) on each side, wrong side in, and press.
    • Double the fold to conceal the rough edge and press again.
    • Sew along the edge of the fold to secure the hem.
  11. 11
    Create the rod pocket.[5]
    • Fold the upper edge of your panel in 0.5 inch (1.25 cm), wrong side in, and press.
    • Fold the clean edge under (wrong side in) again, allowing enough room to compensate for the width of the rod you will be using, and press again.
    • Stitch as near to the folded edge as possible to finish the rod pocket. Once you finish this step, your panel is complete.
  12. 12
    Finished.
  13. Advertisement

Community Q&A

  • Question
    How can I make a privacy kitchen curtain?
    T. Chinsen
    T. Chinsen
    Top Answerer
    Fabric stores sell sheer and lace curtaining fabric, which allow light in and prevent anyone seeing inside. A tension rod can hold the curtain in place if you do not want to install curtain rods. Sheer curtains can also be purchased ready to hang from various stores that carry household items.
Advertisement

Warnings

  • Do not attempt to sew the rod pocket before the hems. Doing so will result in you stitching both ends shut and you will have no way of inserting the rod pockets when you are done sewing your kitchen window treatments.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Tape measure
  • Straight edge
  • Fabric
  • Fabric scissors
  • Iron
  • Fabric marker
  • Sewing machine
  • Thread
  • Rod pocket
  • Sewing gauge

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 106,521 times.
192 votes - 85%
Co-authors: 4
Updated: December 25, 2019
Views: 106,521
Advertisement