How to Test a Heating Element

A simple guide to test a conventional or water heating element

This is a general guide to test any type of heating element for failure using an multimeter to measure the resistance of the element.

Method 1
Method 1 of 2:

Testing A Conventional Element

  1. Image titled Test a Heating Element Step 3
    Image titled Test a Heating Element Step 2
    1
    Know the resistance of the element should be this can be calculated using known values:[1]
    • R = (V x V) / P [Where V is the voltage powering the element, P is the power the element uses and R is the resistance.] (An example calculation is shown in the tips section)
  2. Image titled Test a Heating Element Step 4
    2
    Now we know what resistance we are looking for we can check the element.
    Advertisement
  3. Image titled Test a Heating Element Step 6
    Image titled Test a Heating Element Step 5
    3
    Use a multimeter to find resistance. Set the multi-meter to the resistance setting with an appropriate measuring scale selected. Measure the resistance by disconnecting the heating element from any power source, and connecting the multimeter leads to the terminals of the heating element.[2]
    4. Advertisement
Method 2
Method 2 of 2:

Testing A Water Heater Heating Element

  1. Image titled Test a Heating Element Step 10
    1
    Disconnect the water heater from power source.[3] If it has a disconnectable plug, unplug it. If it does not have a plug, disconnect power by turning off the power breaker or removing the fuse.
  2. Image titled Test a Heating Element Step 11
    2
    Drain the water from the water heater. Locate the water valve at the bottom of the water heater. Attach a garden hose to the emptying valve and turn the valve using a wrench. You will notice a relief valve near the top of the water heater, you can flip the handle up to open it. By doing this it will allow air into the tank causing the water to flow out more quickly.[4]
  3. Image titled Test a Heating Element Step 12
    3
    Wait for the tank to fully empty. Locate the heating element.
  4. Image titled Test a Heating Element Step 14
    Image titled Test a Heating Element Step 13
    4
    Remove the electrical wires leading to the heating element. Then remove the heating element using a socket or a wrench and you can now check the element as shown in first method.
    5. Advertisement

Community Q&A

  • Question
    Why do I multiply two voltages?
    Community Answer
    Community Answer
    Power formula states that P=IV. Ohms law states that V=IR or I=V/R. Substitute V/R for I in the power formula gives us P=V/R*V or V*V/R, so resistance of the element should be the voltage squared divided by the power.
  • Question
    How can I tell if the switch or the element is bad?
    Community Answer
    Community Answer
    If the resistance is higher than calculated or it's infinite (so the circuit is open), then you can assume that the heating element has gone bad. Same thing applies to the switch - if after setting the switch to the "on" position, the resistance is infinite, then it means that the switch doesn't close the circuit and it's broken.
  • Question
    What would cause a microwave to not heat up food?
    Debra Bish
    Debra Bish
    Community Answer
    If your microwave oven quits heating food, it's time for a new microwave oven. There is usually not much else one can do when this happens.
Advertisement

Warnings

  • Take care when dealing with electricity. If you're not confident in your ability to work with electricity then don’t do it. Ask some one who is, such as an electrician or an electrical engineer.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Multimeter or Ohmmeter and Voltmeter

You Might Also Like

Change the Heating Element in a Dryer
How to
Change the Heating Element in a Dryer
Install Baseboard Heating (Electric)
How to
Install Baseboard Heating (Electric)
Make a Voltage Divider Circuit
How to
Make a Voltage Divider Circuit
Set a Boiler Timer
How to
Set a Boiler Timer
Use a Wood Stove
How to
Use a Wood Stove
Test a Thermocouple
How to
Test a Thermocouple
Restart a Furnace After Running out of Oil
How to
Restart a Furnace After Running out of Oil
Bleed an Oil Furnace
How to
Bleed an Oil Furnace
Install a Wood Stove
How to
Install a Wood Stove
Reset a Furnace
How to
Reset a Furnace
Clean a Furnace
How to
Clean a Furnace
Start a Boiler
How to
Start a Boiler
Light a Kerosene Heater
How to
Light a Kerosene Heater
Clean Furnace Flame Rod Sensors
How to
Clean Furnace Flame Rod Sensors
Advertisement

References

  1. ↑ https://www.electronics-tutorials.ws/resistor/res_7.html
  2. ↑ https://www.youtube.com/watch?v=CshL-6Hp2AE
  3. ↑ https://www.youtube.com/watch?v=CshL-6Hp2AE
  4. ↑ https://www.todayshomeowner.com/video/how-to-drain-a-water-heater/

About This Article

Homer Flores
Co-authored by:
Homer Flores
Appliance Repair Specialist
This article was co-authored by Homer Flores. Homer Flores is an Appliance Repair Specialist and Training Manager at PreFix, a home maintenance company out of Austin, Texas. With over 15 years of experience, Homer specializes in home improvement, remodeling, and construction. Homer’s dedication to the PreFix mission of providing hassle-free one-stop-shop service for home care, in addition to their completion of the Capital Factory and Techstars Accelerators, has contributed to their growth of service to over 50 zip codes throughout the greater Austin area. This article has been viewed 370,704 times.
1 votes - 0%
Co-authors: 27
Updated: February 2, 2023
Views: 370,704
Categories: Heating Systems
Advertisement