How to Build a Fuel Cell

To understand how a fuel cell works, you can build a simple electrolytic cell with mostly common household materials. Keep reading to learn how!

Part 1
Part 1 of 2:

Building the Fuel Cell

  1. Image titled Build a Book Lamp Step 8
    1
    Gather all of the necessary materials. To build a simple household fuel cell, you will need 12 inches (30 cm) of platinum or platinum-coated wire, a popsicle stick, a 9-volt battery and battery clip, clear tape, a glass of water, table salt (optional), a thin metal rod, and a volt meter.[1]
    • A 9-volt battery and battery clip can be purchased at an electronics or hardware store.
  2. Image titled Build a Fuel Cell Step 1
    2
    Cut two 6-inch (15-centimeter) strips of platinum or platinum-coated wire. You will need to purchase this wire from an electronics supply store, as platinum isn't used for common wiring purposes. The platinum serves as the catalyst for this reaction.
    • Platinum wires are recommended because other substances, such as copper, will react with the oxygen or the salt to pollute your solution with the products of this reaction.
    • High quality stainless steel can also be used as it will not react as readily.
    Advertisement
  3. Image titled Build a Fuel Cell Step 2
    3
    Wind each wire strip around a thin metal rod to shape it into a spring. These two springs will serve as the fuel cell's electrodes. Take the end of the wire and wrap it tightly around your shaping rod to form a coil. Remove the first wire from the shaping rod and wrap the second wire.
    • The shaping rod can be a nail, pick, wire coat hanger or lead on a battery tester.
  4. Image titled Build a Fuel Cell Step 4
    4
    Cut the leads from a 9-volt battery clip in half. Using a wire cutter, snip both of the wires attached to the clip in half and strip the insulation off the leads. This will leave bare wires that you can attach to your electrode coils.
    • Using the stripping portion of the wire cutters, strip the insulation off of one end of the cut wires. Only strip the ends of the leads you cut off the battery clip.
    • Make sure that you have parental supervision while you're cutting the wires.
  5. Image titled Build a Fuel Cell Step 5
    5
    Attach the exposed wire ends to the electrode coils. Attaching the wire leads to the electrodes allows you to hook up your power source (the battery via the battery clip) and the voltmeter for reading how much electricity the fuel cell is producing.
    • Twist the red battery clip lead and the red clipped wire lead around the top end of one of the coils, leaving most of the coil free.
    • Twist the black battery clip lead and black clipped wire lead around the top end of the remaining coil.
  6. Image titled Build a Fuel Cell Step 6
    6
    Tape the electrodes to a popsicle stick or dowel rod. The popsicle stick needs to be longer than the mouth of the container holding the water so it can rest on top. Tape the electrodes so that they hang down, away from the stick and can be easily submerged into the water.
    • You can use clear plastic tape or electrical tape. It doesn’t matter as long as the electrodes are firmly attached to the stick.
  7. Image titled Make Water Glow Step 13
    7
    Fill the glass with tap water or salt water. In order to get a good reaction, the water solution needs electrolytes.[2] Distilled water does not work well for this because there are no impurities to serve as electrolytes. Salt and baking soda dissolved in water serve as good electrolytes for the reaction.
    • Regular tap water has impurities in it such as minerals that can serve as electrolytes if you don’t have any salt handy.
    • Add a tablespoon of salt or baking soda for each cup of water. Stir until fully dissolved.
  8. Image titled Build a Fuel Cell Step 7
    8
    Lay the stick over the mouth of a glass of water. The coil electrodes should be submerged in the water for most of their length, except where they're connected to the wires from the battery clip. Only the platinum should be submerged.
    • If necessary, tape the stick in place so the electrodes stay in the water.
  9. Image titled Build a Fuel Cell Step 8Bullet2
    9
    Connect the wires coming from the electrodes to a voltmeter or LED bulb. The voltmeter is to show electric current created by the fuel cell once it's activated. Connect the red wire to the meter's positive terminal and the black wire to the negative terminal.[3]
    • You may see a small amount of voltage at this point, such as 0.01 volts, although the voltmeter should read zero at this point.
    • You can also connect a small bulb, such as a flashlight bulb, or a light-emitting diode (LED).
    10. Advertisement
Part 2
Part 2 of 2:

Activating the Fuel Cell

  1. Image titled Build a Fuel Cell Step 9
    1
    Touch the 9-volt battery terminals to the battery clip for one to two seconds. The battery is needed only to send an initial current through the wire to cause the hydrogen in the water molecules touching the electrodes to separate from the oxygen, forming bubbles around the electrodes.[4] This process is called electrolysis.[5]
    • Notice the bubbles forming around each electrode. One electrode has bubbles of hydrogen, while the other electrode has oxygen bubbles.
    • The battery source does not need to be completely attached the clip, just touched to the battery terminals to begin the reaction.
  2. Image titled Build a Fuel Cell Step 10
    2
    Remove the battery. The battery is only needed to initiate the reaction. The separated hydrogen and oxygen will recombine into water, releasing the energy originally used to split them as electricity.[6] The platinum in the electrode coils serves as a catalyst to speed the recombination of the hydrogen and oxygen into water molecules.
  3. Image titled Build a Fuel Cell Step 10Bullet1
    3
    Read the output on the voltmeter. Initially, the output may be as great as two volts, but will decline as the hydrogen bubbles dissipate, quickly at first and then gradually as the last of the bubbles pop.[7]
    • A light bulb or LED may appear bright initially, but will quickly dim and then gradually fade away.
    4. Advertisement

Expert Q&A

  • Question
    What other material could be used for the electrodes besides platinum?
    Bess Ruff, MA
    Bess Ruff, MA
    Environmental Scientist
    Bess Ruff is a Geography PhD student at Florida State University. She received her MA in Environmental Science and Management from the University of California, Santa Barbara in 2016. She has conducted survey work for marine spatial planning projects in the Caribbean and provided research support as a graduate fellow for the Sustainable Fisheries Group.
    Bess Ruff, MA
    Bess Ruff, MA
    Environmental Scientist
    Expert Answer
    You can replace the platinum, but you'll need to make sure that the metal you choose is as non-reactive as possible. Your best option would be one of the other noble metals, which would include gold or silver.
  • Question
    Are these fuel cells used for running vehicles?
    Community Answer
    Community Answer
    No. The vehicles use a different type of fuel cell called a proton exchange membrane fuel cell (PEMFC) which works on the same principal but has a different construction.
  • Question
    How can I power a toy car from a fuel cell?
    Community Answer
    Community Answer
    You can;t, unless your toy car runs on 2 volts and a negligible amount of amps. Powering a toy car with this is akin to flying a Boeing 747 with a model rocket engine.
Advertisement

Warnings

  • While operating this fuel cell, keep it away from open flames or heat sources. Although the amount of hydrogen produced is small, hydrogen is a highly combustible gas.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Platinum wire or platinum-coated nickel wire
  • Thin metal rod (nail, nut pick or similar)
  • A small wooden or plastic dowel or popsicle stick
  • 9-volt battery
  • 9-volt battery clip
  • Transparent tape
  • Salt (optional)
  • Glass of water
  • Voltmeter (or flashlight bulb or LED)

You Might Also Like

Make a Simple Electrical Circuit
How to
Make a Simple Electrical Circuit
Build an EMP Generator
How to
Build an EMP Generator
Make a Simple Electric Generator
How to
Make a Simple Electric Generator
Convert AC to DC
How to
Convert AC to DC
How to
Make a Light out of Batteries
Use a Multimeter
How to
Use a Multimeter
Make a Tesla Coil
How to
Make a Tesla Coil
Build a Motor
How to
Build a Motor
Remember Electrical Resistor Color Codes
How to
Remember Electrical Resistor Color Codes
Make a Burning Laser
How to
Make a Burning Laser
Install a Junction Box
How to
Install a Junction Box
Make an Engine from a Battery, Wire and a Magnet
How to
Make an Engine from a Battery, Wire and a Magnet
Build a Simple Electric MotorSimple Electric Motor Project: Materials & Instructions
Make a Simple One‐Direction Electric Toy Car
How to
Make a Simple One‐Direction Electric Toy Car
Advertisement

References

  1. ↑ http://sci-toys.com/scitoys/scitoys/echem/fuel_cell/fuel_cell.html
  2. ↑ http://americanhistory.si.edu/fuelcells/basics.htm
  3. ↑ https://www.sciencebuddies.org/science-fair-projects/project-ideas/Energy_p002/energy-power/fuel-cells
  4. ↑ http://sci-toys.com/scitoys/scitoys/echem/fuel_cell/fuel_cell.html
  5. ↑ https://www.anl.gov/sites/www/files/2020-09/Hydrogen%20Fuel%20from%20Water_v2.pdf
  6. ↑ http://americanhistory.si.edu/fuelcells/basics.htm
  7. ↑ https://www.sciencebuddies.org/science-fair-projects/project-ideas/Energy_p002/energy-power/fuel-cells
  8. ↑ http://americanhistory.si.edu/fuelcells/basics.htm

About This Article

Bess Ruff, MA
Co-authored by:
Bess Ruff, MA
Environmental Scientist
This article was co-authored by Bess Ruff, MA. Bess Ruff is a Geography PhD student at Florida State University. She received her MA in Environmental Science and Management from the University of California, Santa Barbara in 2016. She has conducted survey work for marine spatial planning projects in the Caribbean and provided research support as a graduate fellow for the Sustainable Fisheries Group. This article has been viewed 170,243 times.
36 votes - 84%
Co-authors: 18
Updated: January 2, 2023
Views: 170,243
Categories: Junior Science Experiments | Electrical Projects
Article SummaryX

To build a fuel cell, start by cutting 2 6-inch strips of platinum wire, and winding the strips around a nail to shape them into springs. Then, cut the leads from a 9-volt battery in half, strip the insulation off the ends of the leads, and attach the exposed ends to the springs. Next, tape the springs to a popsicle stick, and lay the stick over a glass filled with water, so the springs are submerged but the wires are above the waterline. Finally, connect the wires to a voltmeter or LED bulb, so you can see your fuel cell’s current once it’s activated. For information from our Science reviewer on how to activate your fuel cell, keep reading!

Did this summary help you?
Advertisement